Leading 10 usual forklift accidents ， forklift operation should take note of these matters ！.

Do not underestimate the forklift at the office. If the procedure is bad, there will certainly be significant accidents in minutes, and there are many accidents involving forklifts.

Situation 1: The forklift cargo blocked the chauffeur's sight, and the person in front could not be found, resulting in a rolling accident.
Case 2: In order to maintain the equilibrium of the forklift when raising hefty products, the workers used their body weight as the counterweight, which almost caused casualties.
Case 3: The size of the forklift freight surpasses the permitted width of the route and holds on the roadside rack, which practically causes an accident.
Instance 4: Forklift is speeding up and rolls over during a turn.
Instance 5: The forklift vehicle driver did not observe the pedestrian, and the pedestrian did not observe the forklift.
Situation 6: The forklift lifts the employees unlawfully, the forklift chauffeur does not wear the safety belt, the forklift lifter falls and the driver is squashed when the forklift surrender.
Case 7: The forklift vehicle driver did not put on a seat belt and fell from the lorry when it surrendered and was crushed.
Forklift procedure ought to take note of these issues ：.

Begin.
1. Before beginning, observe the surroundings, and after validating that there are no challenges that prevent the security of driving, honk the horn initially and then begin.
2. For cars with hydraulic ( atmospheric pressure) brakes, the brake hydraulic pressure ( atmospheric pressure) gauge must be risk-free prior to starting.
3. When the forklift begins with a tons, the vehicle driver must initially verify that the lots is steady and reliable.
4. The begin must be sluggish and steady.

Driving.
1. When driving, the height in between the bottom end of the fork and the ground ought to be maintained 300mm-400mm, and the pole ought to be slanted backward. .
2. Do not raise the fork expensive when driving. When entering and leaving the job website or while driving, be careful that there will be no barriers overhead. When the load is taking a trip, the fork has to not be raised too expensive, which will certainly affect the stability of the forklift. .
3. After dumping, the fork should be lowered to the typical driving placement before driving. .
4. When turning, if there are pedestrians or cars close by, the driving signal needs to be issued first. High-speed sharp turns are forbidden. High-speed doglegs will cause the car to shed side security and topple. .
5. When the forklift is downhill, it is purely forbidden to turn off the flame and slide, and it is prohibited to brake unexpectedly while driving with lots unless there are unique circumstances.
6. When the forklift is running, it should follow the web traffic rules in the manufacturing facility and have to maintain a particular safety and security range from the vehicle in front. .
7. When the forklift is running, the load must be in the most affordable placement that does not hinder the driving, and the gantry should be effectively tilted back. The lots shall not be elevated other than when stacking or filling. .
8. The elevation of the lots must not block the motorist's sight. In special circumstances, when the product influences the forward vision, drive at a low rate when turning around.
9. It is forbidden to turn on the ramp, nor to drive across the ramp. .
10. The safe driving speed of the forklift in the manufacturing facility location is 5 km/h, and it must drive securely at a reduced speed when entering the Electric Forklift Truck for Warehouse production workshop area. .
11. When the forklift is lifted, raised or driven, it is restricted for employees to depend on the fork to hold products and play a stabilizing duty. .
12. If troubles are located, they will certainly be fixed and reported in a prompt way, and they will certainly never ever run with illnesses or conceal them.

loading and dumping.
1. When fork-loading products, the distance in between both forks should be changed as needed to make the tons of both forks well balanced and not manipulated, and one side of the item need to be against the rack. .
2. It is restricted to deal with Electric Forklift Truck for Warehouse a solitary fork or utilize a fork top or draw. In unique conditions, security warning signs must be established to remind bordering pedestrians. .
3. In the process of packing and unloading products, the forklift should be braked with the brake. .
4. The rate of the automobile ought to be slow-moving and stable. Beware not to roll the wheels on the dunnage, so as not to extend the rolled items and injure individuals. .
5. When utilizing a fork to fork the goods, the fork must be as deep as possible under the load, and it must be noted that the fork idea need to not touch other products or things. The load ought to be maintained with minimal back tilt of the gantry to make sure that the lots does not slide in reverse. The pole can be slanted onward slightly when the load is lowered to permit simple placement of the lots and extraction of the forks. .
6. It is forbidden to fork products at broadband and collide with hard items with the fork head. .
7. When the forklift is functioning, it is prohibited for people to stand around the fork, so as to stay clear of the collapse of the goods and injure people. .
8. Overloading is prohibited, and it is restricted to utilize forks to raise workers to participate in high-altitude operations to prevent high-altitude falling crashes. .
9. It is not permitted to make use of the brake inertia to slide, place, round or roll objects. .
10. It is not allowed to use forks to select, transform pallet unload.

Leaving .
1. It is forbidden to leave the forklift when the items on the fork impend. Before leaving the forklift, you must unload the goods or reduced the fork frame.
2. Pull the parking brake handle to dead or dispirit the parking brake switch.
3. The engine is switched off and the power is cut off. (Except for unique situations, such as the vehicle driver does not leave the car's view and does not exceed 1 min).
4. Remove the trick. .

Forklift Operation Precautions.
1. Before and after the forklift operation, the look must be checked, and fuel, lubing oil and air conditioning water should be added.
2. Inspect the safety and security efficiency of starting, running and stopping.
3. Check whether the lights and horn signals are total and reliable.
4. During the operation of the forklift, inspect whether the stress and temperature level are typical.
5. After the forklift is running, the exterior leak needs to additionally be examined and the seals ought to be changed in time.

Forklift Safety Operation Specifications.
1. You must examine prior to leaving the car;.
2. When you encounter someone in front of you during driving, you ought to send a signal at a distance of 5 m;.
3. The driving speed in the factory does not exceed 5 km/h;.
4. When driving, the low point of the freight need to be 0.3 m ~ 0.4 m in the air;.
5. The transforming need to not be also sharp to stop the propensity of " cost-free switching";.
6. Running up and down the slope must be slow and consistent, and no activating the slope is permitted.
7. Do not drive throughout the slope. When the slope is above 10%, the car should be driven in reverse when declining;.
8. When the forklift personnel lug the goods and progress, if they come across large or hefty products and most likely to the vehicle driver's line of sight, they ought to take the reversing workout
.
The "Eight Prohibitions" need to be adhered to in the procedure.
1. Solitary fork operation is not allowed.
2. It is not allowed to lift the goods for long distance driving.
3. It is not enabled to grab the goods by passing on the pallet with the fork.
4. It is not allowed to straight shovel chemicals, flammables and various other dangerous chemicals with forks.
5. It is not permitted to use inertia force to get the goods.
6. It is not permitted to use braking pressure to expatriation round or easy-to-roll things.
7. It is not allowed to bring people to service the pallet or fork, and it is purely restricted to stand under the fork after the fork is elevated.
8. Do not drive laterally on inclines
.
Vehicle parking is not allowed under the list below problems.
1. Contours, slim roads, railway crossings;.
2. Areas with a longitudinal slope higher than 5%.
3. When there is an obstacle on one side of the road, the opposite side of the section with the exact same size as the challenge must be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：[email protected]
Phone：+86 13827083844